October 30, 2026

ACD/AYC Pump Price: New vs Restored vs Rebuilding Your Own

By STANISLAV, FOUNDER, ACD/AYC PUMPS · UPDATED OCT 30, 2026

Restored pumps from $1,450, rebuilding your own from $400 plus parts, and $150–$350 for your old core.

ACD/AYC Pump Price: New vs Restored vs Rebuilding Your Own

“How much is an ACD pump?” has three honest answers, because there are three ways to fix a failed one: buy a new assembly, buy a restored one, or have your own rebuilt. They differ a lot in price, in how long the car sits, and in what you actually get. Here are real numbers for each, including ours, so you can compare like with like.

SHORT ANSWER

A restored ACD/AYC pump from us costs $1,450–$1,900 depending on the car, with a 12-month warranty. Rebuilding your own pump starts at $400 plus any parts it needs. Your old pump is worth $150–$350 in trade-in credit. A new assembly from Mitsubishi, where you can still get one, costs considerably more.

How much does a restored ACD/AYC pump cost?

These are our current prices for fully restored units — torn down, rebuilt with genuine parts, bench-calibrated and load-tested, with a 12-month warranty:

CARRESTORED PUMPPRICE
Evo X GSR / MRACD/AYC pump, Stage 2$1,700
Evo X RS / Lancer RalliartACD pump, Stage 2$1,450
Evo VII–IX GSR / MRACD/AYC pump$1,700
Evo VII–IX GT / RSACD pump$1,900
Evo IV–VIAYC pump$1,700
Galant VR-4AYC pump$1,600

Prices as of October 2026; the shop always shows the current price. Shipping depends on the destination and is confirmed after you order.

“Stage 2” on the Evo X units means the factory motor has been replaced with a more reliable one as part of the rebuild — the motor is the Evo X pump’s best-known weak point. More on that in how a pump is rebuilt.

How much does it cost to rebuild my own pump?

If you’d rather keep your own unit, you send it to us and pay for the work plus only the parts it actually needs:

WORK OR PARTPRICE
Basic rebuild$400
Stage 2 motor installation$350
Pressure sensor$120
Solenoid (two connectors / one connector)$150 / $200
Hydraulic accumulator$200
Centre housing / main housing$150 / $250

So a pump that only needs the basic rebuild costs $400; one that also needs a sensor and an accumulator is $720. We tell you what yours needs after diagnostics, before doing the work. Most units are turned around in 5–7 days once they reach the workshop. Full details on the rebuild service page.

What about a new pump from Mitsubishi?

New hydraulic units for these cars are expensive, and for the older Evos increasingly hard to find at all. Prices vary by market and dealer, so ask yours for a current quote. Bear in mind that a new unit fixes the symptom but not the reason the old one failed — and on cars this age, the reason is usually corrosion and old fluid that will work on the new pump too unless the system is flushed and bled properly.

Is a used pump a good deal?

Usually not. A used pump from a breaker is the same age as yours and has lived the same life — corrosion inside, tired seals, a motor with unknown hours. There’s no way to tell from the outside whether it builds pressure, and fitting one still means the full job of removal, refit and bleeding. If it’s cheap enough to gamble on, treat it as a core to be rebuilt, not a fix.

How much is my old pump worth?

Through our trade-in programme a failed pump is typically worth $150–$350 in credit towards a restored one, depending on its condition. Send photos, we quote within 24–48 hours, you ship the old unit (shipping is on you) and the credit comes off the price. Please don’t scrap a dead pump — the accumulator holds high-pressure gas and it’s worth money as a core.

Which option makes sense for you?

  • You need the car back quickly: a restored pump from stock, plus trade-in for your old one.
  • You want to keep your own unit, or your car is rare: rebuild your own.
  • You’re a confident home mechanic: the rebuild kits ($150–$570) are the same parts we use — see the spare parts.
  • You’re not sure it’s the pump: don’t buy anything yet. Read the failure symptoms guide and the fault codes first — sensors, relays and low fluid cause the same lights.

Whatever you choose, budget for fitting and a proper bleed — see how to replace the ACD/AYC pump.

Related guides

Related units