November 18, 2026

Buying an Evo? How to Check the ACD/AYC System First

By STANISLAV, FOUNDER, ACD/AYC PUMPS · UPDATED NOV 18, 2026

Six checks from the factory manuals that show whether an Evo's ACD/AYC system is healthy before you buy.

Buying an Evo? How to Check the ACD/AYC System First

An Evo with a dead ACD/AYC system still starts, drives and passes a quick test drive. That’s the problem when you’re buying one: the fault that costs four figures to fix is easy to miss and easy to hide. These are the checks I’d do before handing over money. Each one comes from Mitsubishi’s own workshop manuals, and most need no tools.

SHORT ANSWER

Watch the dash when the ignition goes on, read the stored fault codes, check the fluid level in the boot after the car has stood, look at the tyres, and look for leaks. A clean dash on its own proves nothing: on the Evo X the warning clears itself every time the ignition is cycled.

1. What should the dash do when I turn the ignition on?

CARNORMALFAULT
Evo IV–VIAYC warning lamp lights with the ignition on and goes out after the engine startsLamp stays on with the engine running
Evo VII–IXAll three mode lamps (TARMAC, GRAVEL, SNOW) light briefly, then one stays onAll three stay lit until the ignition is switched off
Evo XThe selected mode is shown on the displayA SERVICE REQUIRED warning appears and the mode display goes off

Two traps here.

A lamp that never lights is also a fault. The manuals list “lamp does not light when the ignition is turned on” as a symptom in its own right. It can be a blown bulb. It can also be a bulb someone removed. Watch for the lamps at ignition-on, before the engine starts.

On the Evo X, the warning resets itself. The manual says the display returns to normal when the ignition is turned off and on again. So an Evo X can show a clean dash at the start of a test drive and the warning comes back later, once the system has tried and failed to build pressure. Drive it long enough, and don’t accept “it only comes on sometimes”. What the warning means is in Service Required 4WD.

If the mode display on an Evo X is flashing, that’s different: the manual describes it as the system protecting itself after hard use, not a fault, and it clears with an ignition cycle.

2. Can I read the fault codes myself?

Yes on the Evo IV–IX, and you should. The codes are kept in memory by battery power even when the lamps are off, and the control unit will flash them on the dash: earth terminal 1 of the 16-pin diagnostic connector, turn the ignition on and count the flashes. The method and the code list are in Evo VII–IX codes; the early cars are in AYC on the Evo IV–VI.

No codes at all isn’t proof either. Disconnecting the battery for ten seconds wipes them, so ask whether the battery has been off recently, and be suspicious of a car that arrives with a freshly reset radio and clock.

On the Evo X you need a scan tool to read the codes. If you’re serious about the car, bring someone who has one. More in MUT-III: what you can do without it.

3. How do I check the fluid?

The reservoir is in the boot on most cars: under a maintenance lid on the Evo VI and VII, behind the right-hand side trim on the Evo X. US-market ACD-only cars are the exception, with the pump and reservoir at the front; see where the pump is on each Evo.

The level should sit between MIN and MAX, but only once the car has stood: the manuals say 90 minutes or more on the Evo VII–X, 5 minutes on the Evo VI. Straight after a drive, part of the fluid is still held under pressure in the accumulator and the level reads low. So check it before the test drive, not after.

A level below MIN means the fluid went somewhere. In the manuals, low fluid and leaks are the first causes listed for a system that isn’t working.

4. Where do I look for leaks?

The manuals name three places: the hydraulic unit and its pressure lines, the transfer case on cars with ACD, and the rear differential (cover and oil seals) on cars with AYC. Look at the unit itself too. On the Evo VII–IX with AYC it sits by the rear left wheel, on the Evo X by the rear right, where it takes years of road spray and salt.

5. Why do the tyres matter?

Because the system compares wheel speeds. Mitsubishi lists tyre size, pressure and wear among the first things to check before any ACD/AYC diagnosis, and there’s a dedicated fault code for a wrong-diameter tyre: code 25 on the Evo VI–IX. On those cars that code doesn’t even light the warning lamp. Four matching tyres with even wear are what you want to see. The manual’s list also includes wheel alignment, a steering wheel that sits straight, and no modifications that affect the system.

6. What should I notice on the test drive?

These are the symptoms from the factory trouble charts:

  • The car struggles to pull away or accelerate on a slippery surface.
  • The rear tyres are noisy in slow, tight corners.
  • Noise from the rear differential while turning.

On a dry road with a healthy-looking dash you may notice nothing at all, which is exactly why the checks above matter more than the drive. Listen for the pump as well, at ignition-on and after the drive: what’s normal and what isn’t is in ACD/AYC pump noise and signs of pump failure.

What can’t I check without a scan tool?

Whether the system actually works under command. The factory operation checks drive the centre clutch and each rear clutch with the scan tool and measure the result, and they read pump pressure live. There’s no manual-approved way to do that from the driver’s seat. If the car is expensive or far away, a specialist inspection with a scan tool is money well spent.

What if the car I want has a fault?

Then it’s a negotiation, not a reason to walk away. Read the codes first: plenty of warnings turn out to be a sensor, a relay or low fluid. If it is the pump, you can put a number on it before you agree a price. Our prices for restored pumps and rebuilds are in ACD/AYC pump price.

Parts for this job

EVO IV–VI · GALANT VR-4

Looking at a car and not sure what you’re seeing? Send me the codes or a photo before you buy.

Related guides

Related units