AYC on the Evo IV, V and VI: How It Differs, Fluids, Codes and Faults
By STANISLAV, FOUNDER, ACD/AYC PUMPS · UPDATED NOV 18, 2026
The first-generation AYC on its own terms: parts, fluids, flash codes and the faults the factory manual lists.

The Evo IV, V and VI are the cars that introduced Active Yaw Control, years before ACD existed. Their AYC is simpler than the later systems and different in the details that matter when you service it: its own control unit, its own fluids, its own fault codes. Most of what’s written online is about the Evo VII–X, and copying it onto an early car is how things go wrong. This is the early system on its own terms. The figures come from the Evo VI factory manual.
On the Evo IV–VI, AYC works alone: there’s no ACD, and the centre differential is a viscous coupling. The hydraulic unit in the boot serves only the rear differential. It runs on ATF SP II (not SP III), the clutch side of the differential takes a dedicated AYC fluid, and the system reports faults through its own AYC warning lamp, which can flash the codes without a scan tool.
How is the early AYC different from the Evo VII–X?
| EVO VI | EVO VII AND LATER | |
|---|---|---|
| Centre differential | Viscous coupling, no ACD | ACD, fed by the same pump |
| Control unit | AYC-ECU, for AYC alone | One ECU for ACD and AYC |
| Pressure monitoring | Pressure switch: on or off | Pressure sensor: a measured value |
| Hydraulic fluid | ATF SP II | ATF SP III |
| Diff clutch-side fluid | Dia Queen AYC Fluid | ATF SP III |
| Fault display | AYC warning lamp | ACD mode indicator / display |
What AYC does is the same on every generation: two clutch packs in the rear differential move torque between the left and right rear wheels to help the car turn. That part is explained in what AYC is and how it works.
Which early cars have AYC?
On the Evo VI, AYC is standard on the GSR and a factory option on the RS. An RS without it has a mechanical limited-slip rear differential instead. The same manual shows the Evo V was built both with and without AYC, and it treats the Evo IV as an AYC car too. If you’re not sure what your car has, look for the AYC warning lamp in the instrument cluster when you turn the ignition on, or send me the VIN.
What are the parts and where are they?
- Hydraulic unit, in the luggage compartment: electric pump (the manual calls it the AYC motor), gas-charged accumulator, pressure switch, a proportioning valve and two directional valves, left and right. The reservoir is reached through a maintenance lid in the boot.
- Torque transfer differential at the rear, with a bleeder screw on each side.
- AYC-ECU, under the front floor console.
- AYC relay, which switches the pump, and an AYC fusible link in the engine-bay relay box.
- Sensors: four wheel speed sensors, the steering sensor on the column, longitudinal and lateral acceleration sensors, throttle position and the stop lamp switch.
Where the pump sits on later cars is in where the ACD/AYC pump is on each Evo.
Which fluids does it take?
| WHERE | FLUID | QUANTITY |
|---|---|---|
| Hydraulic unit reservoir | Dia Queen ATF SP II or equivalent | About 1 L |
| Rear diff, gear side | Hypoid gear oil, API GL-5 or higher, SAE 90 (80W below 10 °C) | 0.41 L |
| Rear diff, clutch side | Mitsubishi Dia Queen AYC Fluid | 0.70 L |
Evo VI workshop manual. The diff plugs are tightened to 49 N·m.
Three fluids, three fills, none of them shared. To check the reservoir, leave the car for at least 5 minutes after driving so the accumulator pressure drops, then read the level between MIN and MAX. (On the Evo VII and later the wait is 90 minutes. This is one of those details that doesn’t transfer between generations.) The differential side is covered in AYC rear differential oil.
How do I read the fault codes?
The Evo VI doesn’t need a scan tool for this. Earth terminal 1 of the 16-pin diagnostic connector, turn the ignition on, and the AYC warning lamp flashes the stored codes: tens first, then units. To clear them, the manual’s method without a tool is to disconnect the battery negative cable for 10 seconds or more.
| CODE | WHAT THE MANUAL SAYS |
|---|---|
| 12 | Power supply voltage to the AYC-ECU out of range |
| 21–24 | Wheel speed sensor, FR / FL / RR / RL — open or short circuit |
| 25 | Wrong-diameter tyre (the warning lamp stays off for this one) |
| 26 | Faulty wheel speed sensor signal |
| 31–34 | Steering sensor — open circuit, short circuit or stuck signal |
| 41 | Throttle position sensor — open or short circuit |
| 51 / 52 | Longitudinal acceleration sensor — circuit / faulty reading |
| 45 / 46 | Pressure sensor circuit — a wiring fault or a faulty pressure sensor |
| 56 | Lateral acceleration sensor — open or short circuit |
| 61 | Stop lamp switch — open circuit or stuck on |
| 65 | ABS monitor — open circuit or ABS fault |
| 71 | Proportioning valve — open or short circuit |
| 72 / 73 | Directional control valve, right / left — open or short circuit |
| 81 | AYC relay — open or short circuit |
| 82 | Electric pump: pressure didn’t come up after the pump was switched on |
| 83 | Electric pump: pressure didn’t drop when the system was commanded to work |
The lamp itself has a normal pattern: it lights when you turn the ignition on and goes out once the engine has started. A lamp that never lights, or stays on with the engine running, is a fault in its own right.
What goes wrong?
The pump can’t build pressure: code 82. The manual’s list of causes starts with the simple ones: low fluid, a leak, the fusible link, the relay, wiring. Then the pump motor and the pressure switch. Check the reservoir level first; it’s the manual’s first step too.
Valves. Codes 71–73 are electrical faults in the valve circuits. You can check the coils with a multimeter at the ECU connector: 3.4–4.0 Ω for the proportioning valve, 15.4–16.4 Ω for each directional valve.
Sensors and tyres. A wheel speed, steering or acceleration sensor fault switches AYC off just as surely as a dead pump. So does a mismatched tyre: code 25 exists for exactly that, and the lamp doesn’t even come on for it.
No code, but AYC isn’t working. The manual lists two symptoms: the car struggles to pull away or accelerate on a slippery surface, or the rear tyres are noisy in slow, tight corners. Its checks run in this order: fluid level and leaks, then the fluid in the differential, then the hydraulic unit and the differential itself.
One more thing the manual is clear on: the valves and the pressure switch aren’t serviced separately. Its answer to a failed valve or switch is to replace the whole hydraulic unit. That’s where a rebuild comes in, because new units for these cars are hard to find.
Can I bleed it myself?
The factory procedure uses the MUT-II scan tool to run the pump and valves while you open the two bleeders on the differential, turning the steering wheel slowly one way for the left bleeder and the other way for the right. The manual warns that a system left with air in it becomes noisy and wears the pump faster. What the tool does and what you can do without one is in MUT-III: what you can do without it.
A tip for jump-starting
This one is straight from the Evo VI manual and almost nobody knows it. If the battery is completely flat and the car misfires and won’t move off on jump leads, either charge the battery properly first, or pull the AYC fusible link from the engine-bay relay box to switch AYC off before you start it. The AYC warning lamp will light, which is expected. Refit the link once the battery has charged and check that the lamp goes out.
Parts for this job
Want to keep your own unit? Send it to our rebuild service, or put it towards a restored one through trade-in.



